Showermiser

Aqua View “Extended Stay” Technology gives you the ability to stay out in your RV longer by conserving both your fresh and gray water capacities up to 40%.

Without changing your tanks or adding weight!

NEVER STEP INTO A COLD SHOWER EVER AGAIN!

We all have busy lives and when we get the chance to take a break, we want to make the most of our camping or boating trips. Time with our families and the memories we make are priceless. As a result the more time we spend enjoying the trip and the less time worrying about the details, the better! How many times have you wanted to stay out camping or boating another day or two, but ran out of fresh water or found out that your gray water tank was full and in need of being dumped?

Have you ever thought about how much fresh clean water gets wasted going down the drain, from the time you turn on the shower, until you’re willing to step in, waiting for it to get warm?

What if there was a way to solve both of these issues?

With SHOWERMI$ER, there is! The SHOWERMI$ER simply connects to your shower outlet. By flipping a small lever, you are able to redirect the cold water back into the fresh water tank, before it even comes out of the showerhead! This water would normally go down the drain, filling up your gray water tank. SHOWERMI$ER, with its unique and patented color-changing ability, will show you in under four seconds that hot water has arrived to the showerhead. Just flip the small lever back to release the water and step into your nice warm shower, without wasting a drop!

NO MORE FRESH CLEAN WATER DOWN THE DRAIN!

money-down-the-drain

WITH “EXTENDED STAY” TECHNOLOGY YOU CAN:

Conserves your fresh and gray water tank capacities up to 40% without changing your tanks or adding weight!

SAVES FRESH WATER

The cost of fresh water is rising to the point that in some places of the world, it’s actually more expensive than gasoline and even rationed!   With SHOWERMI$ER, the amount of fresh water that is wasted taking a shower is greatly reduced with each use!   Generally, lots of cold water goes down the drain, before the water is hot enough to shower.  SHOWERMI$ER redirects that cold water before it gets to the showerhead, back into the fresh water tank until the water is hot.  Not a SINGLE drop is released until you are ready to step into that warm shower!

SAVES GRAY WATER TANK CAPACITY

From the time you turn on the shower in your RV, to the moment you are willing to step into the warm shower, you are not only wasting fresh clean water, but prematurely and unnecessarily filling up your gray water tank.

Wouldn’t you like to save that extra water with each shower? 

Wouldn’t you like to increase your time out in your RV, instead of worrying about

dumping or filling your tanks as often?!

FILL YOUR FRESH WATER TANK FROM INSIDE THE RV

The RV fresh water tank is normally always filled from the outside, which isn’t much fun when the weather is bad!  NO MORE!  When you are at your site and still connected to a water source and ready to fill, simply follow these steps:

  1. Do not disconnect your outside water source.
  2. Check your control panel to see how much fresh water you have in your water tank.
  3. Turn the SHOWERMI$ER lever/valve to bypass the shower head.
  4. Turn the cold water shower valve to full pressure.
  5. Keep an eye on the water control panel.
  6. When it shows full, turn OFF the shower valve.

TANKLESS WATER HEATERS

Tankless water heaters are wonderful for producing continuous hot water, But, did you know they waste even more fresh clean water then a hot water tank system does?

For a tankless water heater to start working a certain amount of cold water must first flow through the system before it fires up.  Additionally a certain “Flow Rate” must be maintained for it to keep producing hot water.

When dry camping or on a boating trip you only have a fixed amount of fresh clean water, so to conserve water most people will take a “military” type of shower.  This is where you turn on the water, get yourself wet, shut off the water, soap yourself up then turn the water back on to rinse off.

While this make good sense to conserve water, it is completely contrary to how a tankless water system works.  The moment you shut off the shower water flow to soap up the tankless system shuts down!

Aqua View to the rescue!  With the SHOWERMI$ER unit installed not only do you save the fresh clean water from going down the drain on “start up”, but during the “soap up phase” as well.  Just by flipping the SHOWERMI$ER leaver back on again, water will stop coming out of the showerhead BUT, will continue to flow so the tankless heater keeps working until you are ready to flip the lever back and rinse off. Continuous hot water and not a drop wasted!

Front Right

ShowermiserSHOWERMI$ER simply connects to your shower outlet. By flipping a small lever, you are able to redirect the cold water from the shower that would normally go down the drain, back into the fresh water tank.

SHOWERMI$ER, with its unique and patented color-change ability, will notify you in under 4 seconds (at normal room temperatures) that hot water has arrived. Once the hot water is present, just flip the lever back to the showerhead and you have hot water ready to go.

NO WASTED WATER
DOWN THE DRAIN,
FRESH AND GRAY
TANK CAPACITIES ARE
INCREASED!

HOW TO INSTALL:

SHOWERMI$ER connects anywhere on the non-pressurized side of the fresh water system, (for example, the fresh water tank or the input side of the water pump).

  1. Simply remove the shower head and attach the SHOWERMI$ER unit.
  2. Line up and mark where the return line will be.
  3. Drill a single hole  (using a hole saw) in the shower wall through to the inside wall where the other plumbing is maintained.
  4. Using the provided lock nut and washer, tighten the SHOWERMI$ER snugly against the wall.
  5. Using a return line with a 1/2″ female pipe thread fitting, attach the return line to the SHOWERMI$ER unit.
  6. Lastly, connect the other side of the return line to anywhere it is convenient on the non-pressurized side of the fresh water system. It is easy!

Items included in the Kit:

  • 1 SHOWERMI$ER unit
  • 1 diverter valve (Chrome, Brushed Nickel or Oil Rubbed Bronze)
  • 1 custom-threaded through wall pipe
  • 1 lock nut & washer to secure unit tightly against the shower wall

*Due to various lengths and installation points, the return line and tank or pump connections, are not included. See your local dealer for parts and/or installation assistance.

SAVE TIME, MONEY AND HELP THE ENVIRONMENT!

This is a win,win, win  for your family, the environment and your pocket book.  Everybody wants to be “Green Thinking” and here is a way to do that while also saving time, money, and increasing your comfort.  We want you to spend less time worrying about your tank capacities and more time HAVING FUN!!

Screen Shot 2016-04-03 at 5.23.36 PMSHOWERMI$ER connects anywhere on the non-pressurized side of the fresh water system, (for example, the fresh water tank or the input side of the water pump). You simply remove the shower head, attach the SHOWERMI$ER unit, line up and mark where the return line will be, and then drill only one hole (using a hole saw) in the shower wall through to the inside wall where the other plumbing is maintained. Using the provided lock washer, tighten the SHOWERMI$ER snugly against the wall.

Using a return line with a 1/2″ female pipe thread fitting, attach the return line to the SHOWERMI$ER unit. Lastly, connect the other side of the return line to anywhere it is convenient on the non-pressurized side of the fresh water system.

What comes in the Kit*:

  • 1 SHOWERMI$ER unit
  • 1 diverter valve (Chrome, Brushed Nickel or ORB)
  • 1 custom-threaded through wall pipe
  • 1 lock nut & washer to secure unit tightly against the shower wall

*Due to various lengths and installation points, the return line and tank or pump connections, are not included. See your local dealer for parts and installation assistance.